Specifications
- Overall dimensions: Length: 139.5 mm ( ~5.5" )
Width: 89.5 mm ( ~3.52" )
Height: 69 mm ( ~2.72" )
- Internal dimensions: See diagrams below.
- Mass: approx 500g
- Basic Enclosure Kit Parts: 1x Body
1x Pedal
1x Bottom Cover
4x Feet
1x Pedal Pad
1x Spring
1x 4PDT switch
13 x 6-32 x 1/4" screws (Zinc plated steel, cross drive #2)
2x Small neoprene foam pads to cushion pedal motion
2x Large neoprene foam pads to secure battery
1x Holdback clip (holds pedal closed)
2x High tensile steel hinge pins (hinge component, fitted to pedal)
2x Nylon bushes (hinge component, fitted to body)
- Materials: Body: Die-cast Aluminium
Pedal: Die-cast Aluminium
Bottom Cover: Electro galvanised steel, primed grey.
Pedal Pad: Textured Polyurethane rubber, black. Other colours will be available in the future
Feet: Rubber, self adhesive
- Switch: Nikkai MB2185SB, no cap.
1/2 " mounting hole
Life > 50,000 operations
4PDT, latching on-on, gold plated contacts for superior signal quality.
(4PDT has one extra set of contacts compared to 3PDT, you can use a 4PDT in place of a 3PDT and have the option of switching another circuit)
Construction of the pedal protects switch from over travel and excess force.
Positive latching switch action you can feel
Enclosure will also accommodate the standard 3PDT switch with 1/2" bush used in many pedals.
- Switch Actuator Travel: Start travel 11.25 mm from switch top mounting surface. Finish travel 7.25 mm from switch top mounting surface
- Battery Compartment: Fit 1x 9V (PP3) battery
Access by two action lift and slide of the pedal. No tools required
- Finish: Unfinished bare aluminium. Powder coated options available on request. Contact for details.
- Internal features: PCB mounting bosses for two layers of circuit board
Dimpled hole centres for fast, accurate drilling of holes for front panel components. (6mm centres, with one extra column dead centre)
- Quality made in New Zealand
Assembly Instructions Link
Width: 89.5 mm ( ~3.52" )
Height: 69 mm ( ~2.72" )
- Internal dimensions: See diagrams below.
- Mass: approx 500g
- Basic Enclosure Kit Parts: 1x Body
1x Pedal
1x Bottom Cover
4x Feet
1x Pedal Pad
1x Spring
1x 4PDT switch
13 x 6-32 x 1/4" screws (Zinc plated steel, cross drive #2)
2x Small neoprene foam pads to cushion pedal motion
2x Large neoprene foam pads to secure battery
1x Holdback clip (holds pedal closed)
2x High tensile steel hinge pins (hinge component, fitted to pedal)
2x Nylon bushes (hinge component, fitted to body)
- Materials: Body: Die-cast Aluminium
Pedal: Die-cast Aluminium
Bottom Cover: Electro galvanised steel, primed grey.
Pedal Pad: Textured Polyurethane rubber, black. Other colours will be available in the future
Feet: Rubber, self adhesive
- Switch: Nikkai MB2185SB, no cap.
1/2 " mounting hole
Life > 50,000 operations
4PDT, latching on-on, gold plated contacts for superior signal quality.
(4PDT has one extra set of contacts compared to 3PDT, you can use a 4PDT in place of a 3PDT and have the option of switching another circuit)
Construction of the pedal protects switch from over travel and excess force.
Positive latching switch action you can feel
Enclosure will also accommodate the standard 3PDT switch with 1/2" bush used in many pedals.
- Switch Actuator Travel: Start travel 11.25 mm from switch top mounting surface. Finish travel 7.25 mm from switch top mounting surface
- Battery Compartment: Fit 1x 9V (PP3) battery
Access by two action lift and slide of the pedal. No tools required
- Finish: Unfinished bare aluminium. Powder coated options available on request. Contact for details.
- Internal features: PCB mounting bosses for two layers of circuit board
Dimpled hole centres for fast, accurate drilling of holes for front panel components. (6mm centres, with one extra column dead centre)
- Quality made in New Zealand
Assembly Instructions Link